Why the Wait Happens

A tankless heater makes hot water quickly, but the water still has to travel the length of the pipe. The cold water already in the line has to flow out first. The farther the fixture, the longer the wait and the more water goes down the drain.

A recirculating pump keeps hot water moving in a loop, so the pipe near the fixture stays warm.

Recirculation Options Compared

There are three common ways to set this up.

Recirculation setups
OptionHow it worksTrade-offs
Dedicated return lineA separate pipe returns water from the far fixture to the heaterBest performance, needs a return pipe
Crossover (comfort) valveA valve under the far sink lets warm water flow into the cold lineNo new pipe, warm cold tap while it runs
Built-in recirculationThe heater has an internal pump and often a bufferNeeds a supported model
Timer or demand controlPump runs on a schedule or button pressCuts energy use, adds a control

The right choice depends on the pipe layout and the heater model.

Waiting too long for hot water?

Call dispatch to talk through a recirculation setup.

Call (773) 207-0518

Details That Decide Success

A pump bolted on without planning wastes energy and can shorten the life of the heater.

Manufacturer approval

Some tankless models allow external recirculation only with a buffer tank or a specific kit. Check the manual before you buy a pump.

Controls

A timer or a motion or button trigger keeps the pump from running all day. Constant running wastes gas and wears the unit.

Pipe insulation

An insulated loop holds heat. Uninsulated pipes in cold basements lose warmth quickly.

Scale and flow

Hard water scale builds in the heat exchanger faster when the unit fires repeatedly. A flush schedule is more important with recirculation.

Water Savings Fit Burbank's Fixture Rules

The Illinois Department of Public Health approved Burbank's ordinances adopting the Illinois Plumbing Code in January 2016, and those ordinances require WaterSense-labeled new and replacement fixtures. The rule reflects a local interest in using less water.

A recirculating loop supports the same aim. It trades a small amount of pump energy for the water that would otherwise run down the drain while you wait.

Source: Illinois Department of Public Health approval of Burbank plumbing ordinances, January 13, 2016.

Is a Recirculating Pump Worth It for Your House?

Not every home needs one. These signs suggest a pump is useful.

  • A bathroom or kitchen is far from the heater
  • You wait a long time for hot water at the same fixtures every day
  • The home has a return line or room to add one
  • The heater model supports recirculation
  • You are willing to set a timer or control

If your heater is near the fixtures that you use, the wait is short and a pump adds little.

What Installation Involves

A plumber checks the pipe layout, finds the best route for a return line and mounts the pump near the heater or at the far fixture. For a crossover valve, the valve goes under the farthest sink and connects hot and cold supply lines.

The pump and controls are tested, and the heater is checked for proper temperature and flow after the system runs. See our tankless water heater service page for what installation covers.

Common Problems After Installation

Complaints come from a few causes. A cold tap that runs warm is usually the crossover valve doing its job. Water that is too hot at the loop is a thermostat setting. A heater that cycles constantly may need a buffer tank or a timer.

If your system cycles on and off often, call for a check. Short cycling shortens the life of the unit.

Comfort and Energy Trade-offs

Recirculation trades a little energy for convenience. The pump uses small amounts of electricity, and the water in the loop loses heat as it travels, so the heater fires to make it up. A timer that runs the pump only at peak times keeps that cost down.

A demand-activated control, such as a button or a motion sensor, is the most economical choice. It starts the pump when you are about to use the tap and stops when the loop is warm.

Questions to Ask the Installer

These questions make a recirculation plan concrete.

  • Does the heater model support external recirculation, and with what kit?
  • Will the system use a return line or a crossover valve?
  • How will the pump be controlled and timed?
  • Is the loop insulated, and who handles it?
  • How does the plan affect the heater warranty?

A clear answer to each of these tells you the installer has thought through the system.

Nearby Homes and Long Pipe Runs

Long pipe runs are common in ranch homes and homes with additions. Homes in Oak Lawn and Stickney frequently have bathrooms at the far end of the house from the basement heater, which is where recirculation helps most.

Dispatch can walk through your layout and suggest the right setup.

Sources and Limits of This Guide

Recirculation advice comes from manufacturer installation guidance, and plumbing details follow the Illinois Plumbing Code, the state standard found in 77 Ill. Adm. Code 890 and administered by the Illinois Department of Public Health.

Always read the manual for your heater model, because recirculation kits differ by brand.

Recirculating Pump Questions in Burbank

It can if the unit is not designed for it. Check the manufacturer's guidance, and use a timer or demand control to limit cycling.

Yes, while it runs. The valve moves hot water into the cold line so the far tap warms faster. The effect fades when the loop cools.

Most are quiet, though a pump close to a bedroom wall can be noticed. Mounting location matters.

The pump uses little electricity. The bigger effect is the gas needed to keep the loop warm, which controls limit.

Often yes, if the model allows it. Check the manual, or call dispatch to confirm.

Questions about recirculation? Call dispatch.

Call (773) 207-0518