Start With How Your Household Uses Hot Water
A heater that is too small runs out during back-to-back showers, and one that is too large wastes energy keeping extra water hot. Sizing starts with the number of people, the number of bathrooms and what runs at the same time, such as a washing machine and a dishwasher.
Tell the plumber about peak mornings and any large soaking tub. Those answers matter more than the age of the house.
Gas or Electric Tank
Most Burbank basements already have a gas line and a flue, which makes like-for-like replacement the simplest path.
Gas tank
- Faster recovery after heavy use
- Needs a working flue and combustion air
- Gas line and shutoff must be sound
- Common in older homes
Electric tank
- No flue required
- Simpler installation in tight spaces
- Needs a dedicated circuit
- Slower recovery on large tanks
Switching fuel types adds work, so many installs keep the existing fuel.
Planning a water heater install?
Call dispatch and share the fuel type, tank size and location.
What an Installation Day Looks Like
A planned install is organized, so you know what is happening at each stage.
Survey
The plumber checks the space, gas line, venting, shutoffs and drain.
Remove
The water is shut off, the old tank is drained and disconnected and hauled away.
Install
The new heater is set, connected with new flexible lines and vented, with an expansion tank where needed.
Test
We check for leaks, verify combustion or elements and confirm the relief line.
City of Burbank Permit and Inspection
The City of Burbank Building Department says a permit is required for the construction or alteration of plumbing and that all contractors must be licensed. It also offers a free inspection on gas water heater replacement that looks at ventilation, the safety valve and the connections.
The office is at 6530 W 79th Street, and the number is 708-599-5500, option 2. We schedule the inspection with you and note the result.
Parts That Come With a Proper Install
The tank is only part of the job.
Expansion tank
A closed system needs a way to absorb expanded water as it heats. Without it the pressure cycles, and the relief valve can start dripping.
Venting and clearances
Gas venting must rise and slope correctly, clear combustibles and carry exhaust out. We test the draft before leaving.
Relief valve and discharge line
The temperature and pressure valve protects the tank. Its discharge pipe goes to a safe place near the floor.
Shutoff and drain pan
A working shutoff on the cold supply and a pan under the tank limit damage if the unit ever fails.
Hardness and the Life of the New Tank
Chicago supplies water to the district serving Burbank, and its 2013 quarterly lab reports listed hardness of 134 to 143 mg/L as calcium carbonate, which is about 8 grains per gallon. That is a 2013 value, so ask the utility for the current figure.
Water in that range builds scale, so plan to flush the new tank yearly and check the anode rod. A softener on the main supply is the next step for homes that see heavy scale, and our softener and filtration page explains it.
What Determines the Installation Price
The price depends on the tank size, the fuel, the venting and any code work. Dispatch gives a price after learning about the existing setup.
You see the price in writing before work starts.
Standards for a Clean Installation
A new water heater needs a relief valve rated to ANSI Z21.22, a discharge pipe that ends where escaping water is visible and a correct gas or electrical connection. The gas side follows NFPA 54.
The permit check follows the Illinois Plumbing Code, the state standard found in 77 Ill. Adm. Code 890 and administered by the Illinois Department of Public Health.
What to Do if You Smell Gas Near the Heater
A gas smell near a water heater is not a wait-and-see problem.
- Do not use switches, lighters or phones near the heater
- Leave the building and take everyone out with you
- Call the gas utility from outside
- Do not re-enter until the utility says it is safe
- Call us after the gas is shut off to arrange the repair
Never try to relight a heater when you smell gas.
Water Heater Installation FAQ
A like-for-like tank swap is often done in a few hours. Changing fuel, moving the heater or replacing venting takes longer.
It depends on the number of people and bathrooms and what runs together. Most households land on a 40 or 50 gallon tank, and the plumber will confirm on site.
Where the home has a check valve, a backflow device or a pressure reducing valve, the system is closed and an expansion tank is recommended. We check this at every installation.
The City of Burbank requires a permit for plumbing alteration and offers a free inspection on gas water heater replacement. We explain the process for your address.
Heat pump models are available, and the right choice depends on space, a condensate drain and an electrical circuit. Ask dispatch about your site.
Ready to schedule an install? Call dispatch.

